Thermal pressure: - Based on wood board interpretation and process production
In the key stage of the production of wood matrix composites, hot pressing has a direct impact on the characteristics and caliber of finished products. The interaction between the heat and mass transfer process during hot pressing and the mechanical deformation process of wood-based composites at high temperatures. In addition, even if resin curing is controlled by the rules of chemical reactions, it may result in heat and water being released or absorbed, which may have an impact on the heat and mass transfer process. After realizing its complex and coupled nature, many scientists have conducted lengthy, multifaceted and multilayered studies to better understand thermal pressure.
A hydraulic press is a machine that uses pressure to generate force, following Pascal's principle. Pascal's law explains that when a force (F1) is applied to a confined fluid on a region (A1), the pressure (P) is transmitted without any reduction, resulting in a force (F2) on the area (A2). This rule can be used to increase the proportion of areas to increase a certain amount of force to produce more force - f2 = f1 (a2/a1)
Multi-daylight hydraulic press is a hot press. It basically consists of a base that encloses one or more hydraulic cylinders, with the ability to rise and fall. The top of the printer uses columns, frames and sturdy metal panels linked to the base. Usually, the height of getting out of bed can be adjusted, while getting into bed remains fixed. The typical thickness of Plato is between 40 and 50 mm, with holes drilled 15 to 20 mm to allow hot oil or steam to pass through. They are made of steel and cast into a single unit. Plato is polished and coated with chrome to prevent glue from sticking to it. Adding a coating enhances the appearance of the panel and acts as a barrier against corrosion. The number of Platons ranges from 3 to 21 or higher, but usually 12 heliograms are used, equal to 13 Platons. The common press plate size in plywood factories is 270 cm x 144 cm and can be used for larger plates with specific needs. The capacity of the pressure varies from 100 tons to 5000 tons. Use a mixture of rotary and piston pumps to produce the necessary pressure. The rotary pump is first used to shut down the press, while the piston pump is used to create and sustain high pressure. The pump needs sufficient capacity to produce a pressure of at least 18 kg /cm2 or higher.
The struts that hold the press can be positioned at corners, sides or ends depending on the layout of the press and ease of loading. These must be strong enough to avoid any bending of the bend and absorb all diagonal pressure. If there is only a slight deflection in the hot spelling, then the pressed component can be handled. However, if significant deflection occurs, the platelets may exert uneven pressure on the components, resulting in insufficient bonding in certain areas of the panel or crushing the wood fibers in specific spots.
Accurate temperature control is most important during hot pressing operations, as temperature changes can lead to very serious failure development. Of the several methods mentioned above, the following three are used commercially to heat plywood presses
During thermal press operation, it is crucial to control the temperature accurately, as any fluctuation will lead to obvious defects. Among the various methods discussed earlier, the following three methods are commonly used commercially to heat plywood presses.
1. Electrical 2. Refueling 3. Steam
Electric heating is expensive and only suitable for very small presses. Steam heating of the press is effective, but comes with an expensive installation process. In India, despite the increasing popularity of heated heating, hot pressing in India is generally favored and widely used.
Precisely plan to minimize any temperature drop with the highest condensation rate to ensure that saturated steam will condense evenly in the channel at a consistent temperature throughout the slat area.
At 10 days of pressure with a 270 cm x x 144 cm platen, steam consumption typically varies from 180 to 275 kg/hr. However, when loading a large charge of a 19mm hardwood veneer assembly, the steam demand can quickly exceed 450kg/hr to maintain the operating temperature. The uniform temperature of the hot press plate can be maintained by appropriate direct temperature control equipment, or the steam pressure can be regulated by the use of sample reduction valves that can be operated manually or automatically.
There are many problems concerning the heating and temperature control of hot platen. One of the main reasons is to compress water vapor in the platens channel through which it passes. Once the condensation layer is formed, it acts as an insulator, thus impeding the transfer of heat from the condensed steam to the surface of the platen by causing water to build up in the platen channel. This can result in significantly lower temperatures, especially at the bottom of Plato.
The solution is to ensure that there is a well-designed platen channel system to prevent large drops during maximum condensation and to maintain uniform steam condensation throughout the platen process. When mixed with steam, air often disrupts the uniform distribution of the surface temperature of the platen. This air is derived from fresh water introduced into the boiler and is completely challenging. As a result, it travels with steam and tends to collect where water condenses and flows slowly. Air cannot condense, and a rich layer of air tends to accumulate near the condensing surface of the channel, reducing the efficiency of heat transfer in these areas.
When a drop in temperature is detected, air in the steam can be removed by placing a purge valve or air bleeding device on the inlet and outlet markers of the Perratu, indicating a potential build-up of air.
Temperature regulation in many hot presses (10 daylight) in India is usually carried out by manual means. It is common practice to connect the temperature gauge to the platen and treat the recorded temperature as the average platen temperature. Depending on the temperature change in the meter, the control valve in the steam line is opening or closing. The position of the bulb of the thermometer can cause uncertainty, as placing it near the steam inlet or outlet may show a different temperature. Not all platons must match the temperature shown by the connected platen. If water accumulates on the pressure plate where the bulb is located, the thermometer will show an inaccurate reading.
Also, taking such temperature readings can be a lengthy process. The steam channel transmits heat through Beragin's metal to reach the thermometer pocket and light bulb, a process that can normally take a lot of time. The bulb needs to be heated first, which also takes time for the thermometer bulb contents to react to the display. In addition to human error and hesitation to quickly open and close the steam line valve, further delays can result.
Due to the accumulation of condensed water trapped inside the Plato, severe temperature fluctuations occurred. Condensate drainage and air binding problems vary greatly depending on platen, header and heater channel design, and steam quality. Due to the slow drainage of horizontal peratu and condensate water, effective steam capture and bypass are necessary. It is important to install a water separator and steam trap at the press inlet to prevent water from entering the Platon, which can worsen drainage problems, and to avoid avoiding air in the steam as much as possible under operating conditions.
This Hot Press is a vital piece of equipment in factories in the plywood industry. The main role of the thermal press is to heat and bake the assembled panels of the face, veneer and core. The steam pressure of the boiler is powering the operating hot press. If the panel is not pressed with the correct steam pressure, high quality results will not be achieved. The technical specifications of hot news actually depend on the annual production demand of the industry. According to the technical specifications, the thermal presses commonly used in the small plywood industry typically have a capacity of 640 tons and include heating plates, bolt boxes, press tables, electrical plates and cylindrical RAM units.






